Lab 15 : Configuring Etherchannel
Langsung saja, download soal latihannya disini :
Lab 15 : Configuring Etherchannel
Soal :
Selesai n selamat mencoba, semoga lab ini bisa bermanfaat.... :D
Lab 15 : Configuring Etherchannel
Soal :
LAYER 2 ETHERCHANNEL :
1. Configure CENTRAL switch interfaces with the following parameters :
- Fa 0/1 and Fa 0/2 as PAGP desirable ports for etherchannel group n°1
- Fa 0/3 and Fa 0/4 as LACP active etherchannel port for etherchannel group n°2
2. Configure SW1 Fa 0/1 and Fa 0/2 interfaces as PAGP auto (etherchannel group n°1)
3. Configure SW2 Fa 0/1 and Fa 0/2 interfaces as LACP passive ports (etherchannel group n°1)
LAYER 3 ETHERCHANNEL :
4. Configure CENTRAL Fa 0/23 and Fa 0/24 interfaces as unconditionnal Layer 3 etherchannel members for port channel 3
5. Configure CENTRAL Port Channel 3 interface with ip address 10.6.0.1/24
6. Configure ROUTER Fa 0/23 and Fa 0/24 interfaces as unconditionnal Layer 3 etherchannel members for port channel 1
7. Configure ROUTER Port Channel 1 interface with ip address 10.6.0.2/24
IP CONNECTIVITY :
8. Configure RIP v2 on CENTRAL and ROUTER devices to enable connectivity between VLAN 1 devices and ROUTER.
9. Test connectivity between Laptop0 and ROUTER.
Jawab :
- CENTRAL(config)#interface range fa0/1-fa0/2
CENTRAL(config-if-range)#channel-protocol pagp
CENTRAL(config-if-range)#channel-group 1 mode desirable
CENTRAL(config)#interface range fa0/3-fa0/4
CENTRAL(config-if-range)#channel-protocol lacp
CENTRAL(config-if-range)#channel-group 2 mode active - SW1(config)#interface range fa0/1-fa0/2
SW1(config-if-range)#channel-protocol pagp
SW1(config-if-range)#channel-group 1 mode auto - SW2(config)#interface range fa0/1-fa0/2
SW2(config-if-range)#channel-protocol lacp
SW2(config-if-range)#channel-group 1 mode passive - CENTRAL(config)#interface range fa0/23-fa0/24
CENTRAL(config-if-range)#channel-protocol pagp
CENTRAL(config-if-range)#channel-group 3 mode desirable - CENTRAL(config)#interface port-channel 3
CENTRAL(config-if)#no switchport
CENTRAL(config-if)#ip address 10.6.0.1 255.255.255.0 - ROUTER(config)#interface range fa0/23-f0/24
ROUTER(config-if-range)#channel-protocol pagp
ROUTER(config-if-range)#channel-group 1 mode desirable - ROUTER(config)#interface port-channel 1
ROUTER(config-if)#no switchport
ROUTER(config-if)#ip address 10.6.0.2 255.255.255.0 - CENTRAL(config)#ip routing
CENTRAL(config)#router rip
CENTRAL(config-router)#version 2
CENTRAL(config-router)#network 192.168.1.0
CENTRAL(config-router)#network 10.6.0.0
ROUTER(config)#ip routing
ROUTER(config)#router rip
ROUTER(config-router)#version 2
ROUTER(config-router)#network 10.6.0.0 - PC>ping 10.6.0.2
Pinging 10.6.0.2 with 32 bytes of data:
Reply from 10.6.0.2: bytes=32 time=11ms TTL=254
Reply from 10.6.0.2: bytes=32 time=16ms TTL=254
Reply from 10.6.0.2: bytes=32 time=14ms TTL=254
Reply from 10.6.0.2: bytes=32 time=7ms TTL=254
Ping statistics for 10.6.0.2:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 7ms, Maximum = 16ms, Average = 12ms
ROUTER#ping 192.168.1.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 7/10/13 ms
Selesai n selamat mencoba, semoga lab ini bisa bermanfaat.... :D
Comments
Post a Comment